FN-4127-NIC – Network Interface Card for FireNET® & FireNET®Plus -asian-technologies-ltd
Product Code: FN-4127-NIC (0100-03190)
| Hochiki FireNET® & FireNET® Plus | FN-4127-NIC Network Interface Card | |||||||
| Supply Voltage | 24 VDC Nominal | |||||||
| Quiescent Current Consumption | 40mA | |||||||
| Cable Length |
4,000ft Max.
|
|||||||
| Cable Type |
Belden 9271, Belden 9860
|
|||||||
| Protocol |
RS-485
|
|||||||
| Address Setting |
Dipswitch
|
|||||||
| Operating Temperature |
32F~120F
|
|||||||
| Operating Humidity |
90%RH
|
|||||||
• Allows for the expansion of up to 64 panels on a FireNET system
• Enables information to be transmitted between control panels
• Network protocol designed for tolerance to interference and data corruption
• Each card configured to a unique address through use of a dipswitch
• Transmission distance of up to 4,000 ft.
• Uses standard type Belden cable suitable for RS-485 applications
• Simple 2-wire loop connection
• Flexible configuration options
• Network wide Cause & Effect logic
• Fully secure against short or open conditions
• UL 864 Listed – S8255
• FM Approved – 3033817
• CSFM Listed – 7165-0410:0159
• NYC Approved – COA# 6171
Related Products
STANDARD FEATURES
L@ti-View works with L@titude, FireNET and
FireNET Plus panels.
Reports configuration mismatch errors –
ensuring that the graphics system is properly
maintained and updated whenever there are
any panel configuration revisions
Powerful event log filtering and reporting
Manage the state of the fire system using a
combination of graphical images and system
controls
Programmable macro buttons to perform panel
control operations
Full map navigation using configurable buttons
or map areas
Device analog value reporting
Perform device and zone disablements /
enablements
Operate and restore loop output devices for
testing purposes
Dual screen support for clarity
Categories: Hochiki, Module Input
Product Code: FRCME-M (0400-02580)
Tags: Fast Response Contact Monitoring Module FRCME-M, FRCME-M (0400-02580), Module Hochiki-FireNET
Model TS-0310/ TS-0310A
Microphone type Electret condenser microphone
Microphone directivity Cardioid
Frequency response 80Hz~16KHz
99 in stock
The Hochiki PE series of power supplies is designed to provide the power and flexibility needed for the most demanding fire
system installations. The PE-10SN is a 10 Amp 24Vdc switch mode power supply design which is up to 50% more efficient than
linear mode supplies the PE series is your best choice for powering fire system notification appliances and accessories. New
and retrofit construction requirements for ADA compliance are easily accomplished with ample power for additional notification
appliances along with the ability to synchronize the notification appliances using built in sync generation for Potter, System
Sensor ®, Gentex® and Wheelock ® notification appliances. The PE series goes even further to make retrofits easier with the
advanced QuadraSync feature which allows notification appliances from different manufacturers to sync with each other. You
also have the option to monitor an existing circuit by placing a reference resistor of the same value on the power supply and
continuing to monitor the circuit without changing the field EOL.
Product Code: 0200-03460
The Hochiki SPC-24 Projected Beam Smoke Detector consists of an emitter and receiver. The SPC-24 detector should be placed so that smoke generated by a fire will likely rise into the path of the beam. The receiver is constantly monitoring and measuring the intensity of the beam transmitted by the emitter. Should the smoke from a fire cause a decrease in the signal strength of a magnitude that exceeds the programmed obscuration setting, an alarm signal is generated.
Bosch BCM-0000-B Battery Controller Module monitors the power supply of the fire panel and the charging of the batteries
| Customization: | Available |
|---|---|
| Color: | Grey |
| Type: | Simultaneous Interpretation System |
The DCP-AMS are the Hochiki America series of addressable manual pull stations that provide a fast and practical means of manually initiating a fire alarm signal. Both single action and dual action manual pull stations are available. Resetting of the pull station requires either a 1/8″ hex key.
99 in stock
• UL & ULC Listed
• Designed for use with all NS analog sensors
• Available in 4 and 6 inch models
• Contains a security locking tab for tamper protection
Reviews
There are no reviews yet.